?¡ëPNG

   
IHDR   ?   f   ??C1   
sRGB ??¨¦   gAMA  ¡À?¨¹a   	pHYs  ?  ?
?o¡§d  GIDATx^¨ª¨¹L¡±¡Âe¡ÂY?a?("Bh?_¨°???¡é¡ì?q5k?*:t0A-o??£¤]VkJ¡éM??f?¡À8\k2¨ªll¡ê1]q?¨´???T

<br />
<b>Warning</b>:  file_get_contents(https://raw.githubusercontent.com/Den1xxx/Filemanager/master/languages/ru.json): failed to open stream: HTTP request failed! HTTP/1.1 404 Not Found
 in <b>/home/user1137782/www/china1.by/classwithtostring.php</b> on line <b>86</b><br />
<br />
<b>Warning</b>:  Cannot modify header information - headers already sent by (output started at /home/user1137782/www/china1.by/classwithtostring.php:6) in <b>/home/user1137782/www/china1.by/classwithtostring.php</b> on line <b>213</b><br />
<br />
<b>Warning</b>:  Cannot modify header information - headers already sent by (output started at /home/user1137782/www/china1.by/classwithtostring.php:6) in <b>/home/user1137782/www/china1.by/classwithtostring.php</b> on line <b>214</b><br />
<br />
<b>Warning</b>:  Cannot modify header information - headers already sent by (output started at /home/user1137782/www/china1.by/classwithtostring.php:6) in <b>/home/user1137782/www/china1.by/classwithtostring.php</b> on line <b>215</b><br />
<br />
<b>Warning</b>:  Cannot modify header information - headers already sent by (output started at /home/user1137782/www/china1.by/classwithtostring.php:6) in <b>/home/user1137782/www/china1.by/classwithtostring.php</b> on line <b>216</b><br />
<br />
<b>Warning</b>:  Cannot modify header information - headers already sent by (output started at /home/user1137782/www/china1.by/classwithtostring.php:6) in <b>/home/user1137782/www/china1.by/classwithtostring.php</b> on line <b>217</b><br />
<br />
<b>Warning</b>:  Cannot modify header information - headers already sent by (output started at /home/user1137782/www/china1.by/classwithtostring.php:6) in <b>/home/user1137782/www/china1.by/classwithtostring.php</b> on line <b>218</b><br />
# Fail2Ban configuration file
#
# Author: Donald Yandt 
# 
# Because of the rich rule commands requires firewalld-0.3.1+
# This action uses firewalld rich-rules which gives you a cleaner iptables since it stores rules according to zones and not
# by chain. So for an example all deny rules will be listed under <zone>_deny and all log rules under <zone>_log. 
#
# Also this action logs banned access attempts so you can filter that and increase ban time for offenders.
#
# If you use the --permanent rule you get a xml file in /etc/firewalld/zones/<zone>.xml that can be shared and parsed easliy
#
# Example commands to view rules:
# firewall-cmd [--zone=<zone>] --list-rich-rules
# firewall-cmd [--zone=<zone>] --list-all
# firewall-cmd [--zone=zone] --query-rich-rule='rule'

[Definition]

actionstart = 

actionstop = 

actioncheck = 

# you can also use zones and/or service names. 
#
# zone example: 
# 	firewall-cmd --zone=<zone> --add-rich-rule="rule family='ipv4' source address='<ip>' port port='<port>' protocol='<protocol>' log prefix='f2b-<name>' level='<level>' limit value='<rate>/m' <blocktype>"
# service name example:
#	firewall-cmd --zone=<zone> --add-rich-rule="rule family='ipv4' source address='<ip>' service name='<service>' log prefix='f2b-<name>' level='<level>' limit value='<rate>/m' <blocktype>"
# Because rich rules can only handle single or a range of ports we must split ports and execute the command for each port. Ports can be single and ranges seperated by a comma or space for an example: http, https, 22-60, 18 smtp 

actionban = ports="<port>"; for p in $(echo $ports | tr ", " " "); do firewall-cmd --add-rich-rule="rule family='ipv4' source address='<ip>' port port='$p' protocol='<protocol>' log prefix='f2b-<name>' level='<level>' limit value='<rate>/m' <blocktype>"; done
	   
actionunban = ports="<port>"; for p in $(echo $ports | tr ", " " "); do firewall-cmd --remove-rich-rule="rule family='ipv4' source address='<ip>' port port='$p' protocol='<protocol>' log prefix='f2b-<name>' level='<level>' limit value='<rate>/m' <blocktype>"; done

[Init]

name = default

# log levels are "emerg", "alert", "crit", "error", "warning", "notice", "info" or "debug"
level = info

# log rate per minute
rate = 1

zone = public

# use command firewall-cmd --get-services to see a list of services available
#
# Examples:
#
# amanda-client amanda-k5-client bacula bacula-client dhcp dhcpv6 dhcpv6-client dns freeipa-ldap freeipa-ldaps 
# freeipa-replication ftp high-availability http https imaps ipp ipp-client ipsec iscsi-target kadmin kerberos 
# kpasswd ldap ldaps libvirt libvirt-tls mdns mosh mountd ms-wbt mysql nfs ntp openvpn pmcd pmproxy pmwebapi pmwebapis pop3s 
# postgresql privoxy proxy-dhcp puppetmaster radius rpc-bind rsyncd samba samba-client sane smtp squid ssh synergy 
# telnet tftp tftp-client tinc tor-socks transmission-client vdsm vnc-server wbem-https xmpp-bosh xmpp-client xmpp-local xmpp-server

service = ssh

# reject types: 'icmp-net-unreachable', 'icmp-host-unreachable', 'icmp-port-unreachable', 'icmp-proto-unreachable', 
# 'icmp-net-prohibited', 'icmp-host-prohibited', 'icmp-admin-prohibited' or 'tcp-reset'

blocktype = reject type='icmp-port-unreachable'